Routing RIPv2
Desember 14, 2018
Add Comment
Kali ini saya akan memposting bagaimana membuat routing secara static. Jenis routing ini memakai konsep network mana yang akan di routing dan memakai gateway yang menuju network tersebut.
Pengaturan port di setiap router
Klik R1 lalu tambahkan port (HWIC-2T) untuk kabel serial.
Hingga menjadi seperti ini.
Lakukan langkah tersebut pada router berikutnya, lalu hubungkan kabel Serial DCE dari R1 ke R2 juga ke R3.
Pengalamtan IP
R1
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ho R1
R1(config)#int g0/0
R1(config-if)#ip add 192.168.1.1 255.255.255.0
R1(config-if)#no shut
R1(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
R1(config-if)#ex
R1(config)#int se0/0/0
R1(config-if)#ip add 10.1.0.1 255.255.255.252
R1(config-if)#clock rate 128000
R1(config-if)#no shut
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to down
R1(config-if)#ex
R1(config)#
R2
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ho R2
R2(config)#int g0/0
R2(config-if)#ip add 192.168.2.1 255.255.255.0
R2(config-if)#no shut
R2(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
R2(config-if)#ex
R2(config)#int se0/0/0
R2(config-if)#ip add 10.1.0.2 255.255.255.252
R2(config-if)#no shut
R2(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
R2(config-if)#ex
R2(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up
R2(config)#int se0/0/1
R2(config-if)#ip add 10.1.0.5 255.255.255.252
R2(config-if)#clock rate 128000
R2(config-if)#no shut
%LINK-5-CHANGED: Interface Serial0/0/1, changed state to down
R2(config-if)#ex
R2(config)#
R3
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ho R3
R3(config)#int g0/0
R3(config-if)#ip add 192.168.3.1 255.255.255.0
R3(config-if)#no shut
R3(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
R3(config-if)#ex
R3(config)#int se0/0/0
R3(config-if)#ip add 10.1.0.6 255.255.255.252
R3(config-if)#no shut
R3(config-if)#
%LINK-5-CHANGED: Interface Serial0/0/0, changed state to up
R3(config-if)#ex
R3(config)#
Berikan ip address untuk PC0,PC1 dan PC2.
Routing Static
R1
R1(config)#
R1(config)#ip route 192.168.2.0 255.255.255.0 10.1.0.2
R1(config)#ip route 10.1.0.4 255.255.255.252 10.1.0.2
R1(config)#ip route 192.168.3.0 255.255.255.0 10.1.0.6
R1(config)#
R2
R2(config)#
R2(config)#ip route 192.168.1.0 255.255.255.0 10.1.0.1
R2(config)#ip route 192.168.3.0 255.255.255.0 10.1.0.6
R2(config)#
R3
R3(config)#
R3(config)#ip route 192.168.2.0 255.255.255.0 10.1.0.5
R3(config)#ip route 10.1.0.0 255.255.255.252 10.1.0.5
R3(config)#ip route 192.168.1.0 255.255.255.0 10.1.0.1
R3(config)#
Setelah selesai coba kirim pesan dari PC0 ke PC1 atau PC2, bila gagal ulangi pengiriman.
Bila ada pertanyaan comment dibawah, Jangan lupa share bila bermanfaat ^^.
Salam TKJ
0 Response to "Routing RIPv2"
Posting Komentar